It is usually found in the installation directory or somewhere similar to "murmur / murmur.ini" or "/etc/murmur.ini". Otherwise, your server will be open to anyone who finds it.Īfter installing Murmur, search the system for a file called "murmur.ini". You will also need to do this if you want your server to be private, only available to people you invite, and password provided. This step is only necessary if you have specific requirements for your server, such as bandwidth or a limited number of users, or a specific port usage. There are links for both Mumble and Murmur, so make sure you have Murmur (also known as mumble-server) installed on your server and Mumble on any device you'll use for voice chat. Refer to the Mumble download page for links to the latest version for your operating system. You can use to find instructions for your particular router model. If you go through this process and still can't connect to your server, you may also need port forwarding on your router. To make sure the portal is open properly, you can check it out with a site like. If you are using third-party security software, you also need to make sure they don't close the port either. If not, you'll have to look up how to do this manually on your particular operating system. Windows may automatically ask when you launch Murmur, if you want to open its default port. The default port Murmur uses is 64738, but you can choose a different port if you want.Ĭompletion of this will also depend on the device settings. You will need to open a port on your device so that the client won't be blocked from connecting to the Mumble server. Do a quick search "static ip " for instructions. The setup process can vary quite a bit depending on the operating system and the connection type. Static IP will allow Mumble users to always find your server in the same place. You need a static IP address to run Murmur. Configure the network settings in advanceīefore attempting to install and run Murmur, it is important that you properly configure the system that hosts it. Your screen might look a little different. You can set up Murmur on Windows, Linux or macOS (we use Linux Mint). The server-side application to host Mumble is called Murmur. If you want to be expensive and have full control over your Mumble server, then read on. Remember to restart the service to reload settings with the following command sudo service mumble-server restartĪt this point your server is ready for use.Available services will host such a server for you as well, but may require a fee. registerName – changing this will change the default channel’s name, set to whatever you want.Setting to true will expose the server’s current and maximum user count, as well as some other information. allowping – decide if you want your server to be reachable with ping command.For every 1GB of ram on your machine you can serve about 100 users users – this will denote the maximum number of concurrent users that can be connected to your server.serverpassword – you can put your server password here.welcometext – this will be the text that is displayed upon connection to the server, remember to put the text in quotes.Unless you want it to be elsewhere, leave the default logfile – this will be your default log file location.There are a few parameters that you should change In order to use those parameters, you have to remove that character. Note! By default, some values have a semicolon ( ) at the start of the line. In order to modify it, run the following command sudo nano /etc/mumble-server.iniĬaution! Do not change values if you are unsure of what they do! Mumble provides a configuration file to tweak your server settings. Type in a password that will be used for your administrative account on the server. If not started with root privileges, client will not be able to access your LetsEncrypt certificate in the default folder! SuperUser password If you want your server to prioritize Mumble service to allow for better connection, answer Yes.Ĭaution! If you want to use your own SSL certificate for encryption, you have to use high priority, as Mumble is then started with root privileges. Otherwise the server can be started with the following command sudo service mumble-server start Network priority If you want to start Mumble server after the machine boots up, answer Yes. This will bring up a short configuration, if at any point you want to change settings, you can run the command again. Run the following command sudo dpkg-reconfigure mumble-server By default, Mumble uses a self-signed certificate, there is no password and all data in config file has default values.įirst, you need to change a few settings and setup the SuperUser password for admin access on your server by reconfiguring mumble-server package
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |